10665014
Used-Reifenhauser 1800mm (70") sheet extrusion line consisting of 120mm (4.7"), 33 L/D Reifenhauser extruder with 200 kW (266 hp); screen changer, gear pump, 1700mm (67") die, 3 roll stack, haul off and guillotine; Vollmar 4 component volumetric blender system with blowers, Gneuss screen changer, Reinhardt guillotine. Year of production 1995. details
|
41343001
Used- HPM Sheet Line Consisting Of: (1) HPM 4-1/2'' single screw extruder, model 4.5TMIII, serial# 82-210. Approximately 30 to 1 L/D ratio. Electrically heated, water cooled 6 zone non-vented barrel, with pump, and heat exchanger, no holding tank. Approximate 34-1/2'' center line height. Water cooled feed throat with hopper. Driven by a 200 hp, 460 volt details
|
|
|
41231001
Used-Davis Standard Multi-Layer Sheet/Thermoforming Line consisting of the following: (1) Davis Standard model 60IN60TPIH, 6" screw diameter, 30:1 L/D ratio, electrically heated, water cooled, 500 hp DC drive thru 17.2:1 gearbox ratio. (2) Davis Standard model 100MM35F, 3.9" screw diameter, 30:1 L/D ratio, electrically heated, water cooled, 125 hp DC details
|
41157002
Used- HPM SHEET TAKE OFF SYSTEM INCLUDING THE FOLLOWING: .HPM MODEL SHEETMASTER III SHEET TAKE OFF HAVING (3) 54" FACE X NOMINAL 24" DIAMETER ROLLS. ONE ROLL IS CHROME PLATED AND TWO ROLLS ARE MATT FINISHED. EACH ROLL IS DRIVEN BY A 5 HP AC MOTOR THROUGH A GEAR REDUCER HVING A 450/1 REDUCTION RATIO. HYDRAULIC ROLL ACTUATION WITH THREE HP HYDRAULIC PUMP. TEMPERATURE details
|
|
|
10665009
Used-1040mm (approx 40") Welex Co-extrusion Sheet Line. 115mm (4.5") extruder, gear pump, static mixer, co-ex block, 1040mm (40") x 450mm (18") 3 roll stack, pumps, haul off, 2 station winder. 115mm Welex single screw extruder. 7 zone water cooled barrel. Vented. Hydraulic lantern slide screen changer with power pack, model 450, 30:1 RHS.V. 149 rpm max details
|
10665008
Used-1350mm wide Welex coextrusion sheet extrusion line. 90mm + 50mm extruders, flex lip die, 1350mm x 450mm 3 roll stack, double haul off, pump group. 90mm Welex single screw extruder, 30D. 226 rpm screw - high output. Water cooled, electrically heated brrel. Vented. 150 hp DC motor, 1983. Hydraulic lantern slide screen changer. ABA type Welex square details
|
40362002
Used-Kuhne sheet extrusion line with an output of 374 lbs (170 kgs)/hour consisting of: (1) Morette Plastic System mixing/feeding system; (1) Kuhne single screw extruder, 30 mm, 30:1 L/D, electrically heated, air cooled; (1) melt pump; (1) EDI Ultra Flex H75 650 mm; (1) 25.4" (650 mm) sheet roll stack; (1) pulling unit; (1) winding unit station; (1) Kurtx details
|
10665007
Used-1600mm wide Union sheet coextrusion line. 120mm, 60mm single screw extruders, melt pump, 1500mm die, 1600 x 450mm polishing stack, guillotine, 2000. 120mm Union single screw extruder. Electrically heated, fan cooled barrel. 35D vented. 210 kW DC motor with drive. Union 30 hp AC melt pump. Year 2000. 60mm Kuhne coextruder, vented, 33:1D. 1600mm wide details
|
10665006
Used-1200mm Amut coextrusion sheet line: 90mm extruder, 50mm coextruder, changer, gear pump, coex block die, 3 roll stack, haul off, winder, hyd nip, 1993. 90mm single screw extruder circa 32:1 L/D ratio. 117 kW DC motor, electrically heated, air cooled barrel. 17 kW DC motor. DC drive panel, 18 zone operator's temp control panel. Barrel currently vented details
|
REQUEST PRICE QUOTE
Width (in.): 57.08
Manufacturer: Omipa/Repiquet
Roll Diameter (in.):
Model:
10665005
Used-1450mm wide Omipa/Repiquet sheet extrusion line, 120mm Omipa extruder, melt pump, Omipa 1450mm die, Repiquet 5 roll stack, haul off, shear, 1991. 120mm Omipa extruder OM120 1990, serial 90177, 33D vented, 141 kW DC motor, electrically heated fan cooled, 7 zone barrel. 21 zone temperature control panel, DC thyristor control panel. 120mm lantern slide details
|
10665004
Used-1700mm wide Kuhne coextrusion sheet line, comprising 105mm extruder, 30mm coextruder, 1650mm wide Vergruggen die, 1700 x 400mm roll stack, haul off, 1988. 105mm Kuhne single screw extruder 33D. Fan cooled barrel, vented. 150 kW DC motor (2 sets of drive pulleys to adjust torque range). Electrically heated fan cooled barrel, spare grooved feed zone sleeve, details
|
10665003
Used-1750mm wide Battenfeld sheet line, 115mm single screw extruder, 70/70 gear pump, 1750 x 400mm 3 roll stach, haul off, guillotine, 1991. 115mm diameter single screw Battenfeld extruder. 30D plugged vent, 7 zone electrically heated fan cooled barrel, serial A14747, 19:1 gearbox ratio, 214 kW DC motor. 115mm hydraulically operated lantern slide screen details
|
10665001
Used-890mm wide Welex Coextrusion sheet line. 90mm main extruder, 50 mm coextruder, 890x300mm rolls, pump group, haul off, 2 station winder, 1990. 90mm Welex single screw extruder, 30D vented. Water cooled barrel. 100 hp DC motor and drive. Hydraulic screw changer with power pack, and accumulator. Maag model 56/3T gear pump (2000) with DC motor and details
|
REQUEST PRICE QUOTE
Width (in.): 54
Manufacturer: BATTENFELD GLOUCESTE
Roll Diameter (in.): 16
Model: 244-001
40508004
Used- Battenfeld Gloucester Laminating Line consisting of: (1) Battenfeld Gloucester 4 1/2'' single screw extruder, model 244-001, 24 to 1 L/D ratio, electrically heated, water cooled side vented 5 zone barrel. Water cooled feed throat with hopper. Approximate 43'' centerline height. Driven by a 150 hp, 500 volt, 1750/2000 rpm DC motor thru a gearbox, ratio details
|
REQUEST PRICE QUOTE
Width (in.): 54
Manufacturer: BATTENFELD GLOUCESTE
Roll Diameter (in.): 16
Model: 244-001
40508005
Used- Battenfeld Gloucester Laminating Line consisting of: (1) Battenfeld Gloucester 4 1/2'' single screw extruder, model 244-001, 24 to 1 L/D ratio, electrically heated, water cooled side vented 5 zone barrel. Water cooled feed throat with hopper. Approximate 43'' centerline height. Driven by a 150 hp, 500 volt, 1750/2000 rpm DC motor thru a gearbox, ratio details
|
REQUEST PRICE QUOTE
Width (in.): 62
Manufacturer: BATTENFELD GLOUCESTE
Roll Diameter (in.): 1
Model: 244.001
40508006
Used- Battenfeld Gloucester Tandem Foam Extrusion Line consisting of: (1) 4.5" Battenfled Gloucester extruder, model 244.001, 36:1 L/D, electrically heated, water cooled, jacketed feed section with 150 hp DC motor with SCR controller, serial #244.29812.01. (1) 4.5" Beringer hydraulic screen changer. (1) 6" Battenfeld Gloucester extruder, model 266.001, details
|
|
|
REQUEST PRICE QUOTE
Width (in.): 54
Manufacturer: GLOUCESTER
Roll Diameter (in.):
Model: 267-001
40578001
Used- Gloucester 54'' wide foam line consisting of: (1) Glouster 6'' single screw extruder, model 267-001, approximately 30 to 1 L/D ratio. Electrically heated, water cooled barrel, approximate 42'' center line height. Driven by a 200 hp, 500 volt, 1750 rpm DC motor thru a reducer, ratio 41.83 to 1. Includes a die clamp. (1) Glouster 4 1/2'' single screw details
|
40550001
Used- OMV 3 Roll Sheet Stack. (3) Approximately 20'' diameter x 47'' wide chrome plated cored rolls with (2) approximate 20'' diameter x 47'' wide chrome plated cooling rolls, all driven by a 3 kw, 320 volt, DC motor with reducers. Cooling rolls chain driven off of center roll. (1) Sussex Instruments mechanical thickness gauge with controls, serial# 5L2-STM1070; details
|
40505002
Used- PTI Trident Series Multi Layer Sheet Extrusion System consisting of: (1) Used 6" PTI Trident Series Extruder, model 6000, 28:1 L/D electrically heated, air cooled, 7 barrel zones, jacketed feed section, 21.75:1 gearbox ratio, 400 hp, 1791/2686 rpm AC motor, with Dynisco hydraulic screen changer, Gravimetric material loader and 40 hp gear pump. (1) details
|
40453002
Used- PTI multi-layer sheet extrusion line including the following: A) (1) Used PTI model 6000 Trident series 6", 28:1 extruder having a 7 zone electrically heated, air cooled barrel at an approximate 94" centerline height. Gearbox is a Flender model SZNS-390, has reduction ratio of 21.756:1, has a service rating of 400 hp and a catalog rating of 701 details
|
|
|
523936
USED: Union 47.2" (1200mm) sheet extrusion line consisting of: (1) 3.54" (90mm) Union single screw extruder, electrically heated, power 50 kW, fan cooled barrel, 30D vented, driven by a 61 kW motor with drive; (1) sieve change, diameter 2 x 4.7" (120mm), hydraulic unit, heating power 6 kW; (1) Union 3 stack calander, roll diameter 11.8" - 13.8" - 11.8" (300-350-300mm), details
|
REQUEST PRICE QUOTE
Width (in.): 1.5
Manufacturer: Davis Standard
Roll Diameter (in.): Davis
Model:
523797
USED: Davis Standard stretch tape line for lab or pilot plant use. Complete with (1) used Davis Standard 1.5" thermatic extruder, 24:1 L/D, vented and plugged, electrically heated, air cooled, complete with control panel, 4 barrel zones, 1 adapter zone, 3 die zones, 10 hp variable speed drive. (1) Stainless steel quench tank. (1) 8" x 33" MPM 3 roll Godet details
|
89095
USED: Battenfeld 17.5" wide sheet/cast film line consisting of: (1) Battenfeld 60 mm (2.3") single screw extruder, model 1-60-30DV, serial #89-7782-62, approximate 30:1 L/D ratio, 5 zone non-vented barrel, electrically heated, air cooled. Driven by a 52 kw (70 hp), 460 volt DC motor thru a gearbox with control panel. (1) Battenfeld 45 mm (1.7") single screw details
|
REQUEST PRICE QUOTE
Width (in.): 50
Manufacturer: Processing Technolog
Roll Diameter (in.): Proces
Model: 5024
523574
USED: Processing Technologies Inc model 5024 3 roll down stack.Manufactured 2/2000. 24" diameter x 50" wide lower 2 chrome rolls,upper roll is 12" x 50". All chrome rolls cored for cooling. Rollsare hydraulically operated and powered by a 7.5 hp DC motor viasilent chain drive, Control Techniques Mentor II DC drives for stackand pull roll station, pull details
|
REQUEST PRICE QUOTE
Width (in.): 34
Manufacturer: Cincinnati Milacron
Roll Diameter (in.): Cincin
Model:
523575
USED: Cincinnati Milacron 3 roll stack/laminator. Two cored forcooling chrome rolls 17.75" diameter x 34" wide; two aluminum guiderolls, one 17.74" diameter x 31" wide and one 8" diameter x 31" wide.Chrome rolls are pneumatically operated and are powered by a 5 hp,1750 rpm, 500 volt DC motor thru a Koellmann 18.131:1 gearbox viasilent chain drive, rolls details
|
523560
USED: Three roll sheet stack. (3) rolls with 33" face x 12" diameter cored rolls, with hydraulic gap adjustment, single row, chain driven with 3 hp 230/460 volt motor with variable frequency drive, 5" diameter x 34" face rubber nip roll assembly with hydraulic gap adjustment and 2 hp 230/460 volt motor with variable frequency drive. details
|
REQUEST PRICE QUOTE
Width (in.): 51
Manufacturer: Gefran
Roll Diameter (in.): Gefran
Model: TN75
523526
USED: Gefran sheet extrusion line. (1) Extruder Tr1-75/35, screw diameter 2.95" (75mm), degassing, 380V/50 hz/3 ph; (1) die head 51"(1300mm); (1) 3 roll calander type CL1, width 51" (1300mm), diameter 13.4" (340mm), max opening 2.76" (70mm); (1) haul off TRL 51" x 7.9" (1300mm x 200mm), opening max 3.9" (100mm); cutting unit TLS 1300; (1) lifting platform; details
|
523528
USED: Union 58.5" (1500mm) sheet co-extrusion line consisting of:(1) 120mm Union single screw extruder, electrically heated, fancooled barrel, 35D vented, 210 kw DC motor with drive; (1) Union30 hp AC melt pump; (1) Kuhne 60mm co-extruder, vented, 33:1D;(1) approximate 58.5" (1500mm) wide flex lip die with choker bar;(1) Union 3 roll polishing stack, details
|
523504
USED: Amut sheet line. (1) Amut DS co-rotate extruder 5.7" (145mm) 20D, screen changer, melt pump, degassing, motor 212 hp (156 kw), 400 volt/3 phase, 50 hz. (1) Piovan gravimetric dosing system, 3 components. (1) Die head 33" (840mm), flexible lips; (1) die head 48" (1220mm) flexible lips; (1) die head 60" (1525mm) flexible lips; (1) new spare gear unit; details
|
523505
USED: Amut sheet line. (1) Amut DS co-rotate extruder 5.7" (145mm) 20D, screen changer, melt pump, degassing, motor 212 hp (156 kw), 400 volt/3 phase, 50 hz. (1) Piovan gravimetric dosing system, 3 components. (1) Die head 33" (840mm), flexible lips; (1) die head 48" (1220mm) flexible lips; (1) die head 60" (1525mm) flexible lips; (1) new spare gear unit; details
|
REQUEST PRICE QUOTE
Width (in.): 12
Manufacturer: Berstorff
Roll Diameter (in.): Bersto
Model: ZE25
523507
USED: Berstorff twin screw extruder line. (1) Berstorff extruder 1" (25mm), type ZE25 40D, Feller control panels included. (2) Berstorff feeding units, ZSFE-DDSR20. (1) Busch vacuum pump; (1) die head 150 x 0 to 4 cubic mm; (1) 3 roll calendar, temperature control by oil. (3) Brabender scale 2xDDW-P3-DDSW20N-15, 1xDDW-P3-DDSR20N, Brabender Congrav L/M-2 details
|
523006
USED: Three roll sheet stack. (3) rolls with 33" face x 12" diameter cored rolls, with hydraulic gap adjustment, single row, chain driven with 3 hp, 230/460 volt motor with VFD, 5" diameter x 34" face rubber nip roll assembly with hydraulic gap adjustment and 2 hp, 230/460 volt motor with variable frequency drive. details
|
|
|
|
|
REQUEST PRICE QUOTE
Width (in.): 60
Manufacturer: Breyer
Roll Diameter (in.): Breyer
Model: MONO EXTRUDER
522861
USED: Breyer 60" (1560mm) sheet line for 1.5 mm sheet thickness x 1500 mm with a capacity of 808 lbs/400 kgs per hour consisting of: (1) feeding/blending system; (1) Breyer single screw extruder, type Mono, 30:1 L/D, 4.6" (120 mm) diameter screw, electrically heated, air cooled, vented; (1) Maag Extrex 56/56 gear pump; (1) Breyer 60" (1560) sheet die head details
|
|
|
86659
USED: Welex sheet extrusion downstream stack. 3 rolls measure 18" diameter x 41" face width. Two chrome, one ceramic. Rolls are chain driven by a 5 hp DC drive. Pneumatically operated roll closure. Unit includes heat exchanger pumps for roll temperature control. Rubber pull rolls are unitized to frame. Unit does not include the standard rubber pull rolls. details
|
84979
USED: 2000mm Omipa coex sheet line. 120mm extruder, gear pump, coextruder, coex block, fastgap die, 2000mm Omipa 3 roll inclined stack, conveyor, haul off.
* 120mm Omipa model OM120 single screw extruder. Vented. Fan cooled, electrically heated. Serial no 88102, 160kw dc motor with Thyristor drive. Hydraulic lantern slide screen changer. OM 65 gear pump, details
|
|
|
|
|
REQUEST PRICE QUOTE
Width (in.): 66
Manufacturer: Davis Standard
Roll Diameter (in.): 20.8
Model:
82270
USED: Davis Standard sheet take-off unit consisting of (3) 66" face by nominal 20.8" diameter rolls, mounted in a vertical arrangement for an upstack operation. Unit includes (7) total rolls: (3) chrome rolls having a 2 to 4 RMS finish, (2) matte finish rolls, (1) ceramic roll and (1) silicone rubber roll. Rolls are hydraulically actuated. (1) 3 zone details
|
521446
USED: 70" wide APV sheet extrusion downstream. Package includes 12" x70" 3 roll stack (3 matte finish, 1 polished chrome), each roll withindividual roll drive utilizing 3 hp AC motors with Sabina inverters.208/230/460 volt AC input for roll drives. Chrome roll stack ishydraulically loaded and includes 5 hp hydraulic pumping system andbuilt under frame temperature details
|
521330
USED: APV Sterling extrusion line for the production of PP filamentfor woven sacks/bags. Line includes (1) APV Sterling 4.5" extruder,30:1 L/D ratio single screw extruder, 200 hp main drive motor;(1) Polynetics 4 component blender, hoppers loaded by Conair modelDL 12 vacuum receivers, 3 augers are driven by 1/8 hp variable speedmotors. System discharges details
|
81573
USED: NRM 78" wide 3 roll sheet stack. (1) 16" diameter pattern cored roll, (2) 16" diameter chrome cored rolls, manually adjustable. Driven by a 5 hp, 180 volt DC motor with reducers. Frame mounted with pumps and heat exchangers, approximately 12' long section of roller conveyor, (1) control panel with Eurotherm 808 digital controllers. (1) NRM 2 roll pull details
|
REQUEST PRICE QUOTE
Width (in.): 42
Manufacturer: Davis Standard
Roll Diameter (in.): 18
Model:
520628
USED: Davis Standard 3 roll down stack. 18" diameter x 42" wide,cored for cooling, chrome rolls, 3 hp DC motor through gearboxpowering silent chain drive, hydraulic pressured rolls. Chrome rollsare cooled by two Conair/Tempro model TC2-DI thermolators, 460 volts,26.3 max amps, 9 kw each. 3 hp pump, digital display SPI compatibleRS232 communications port, details
|
REQUEST PRICE QUOTE
Width (in.): 54
Manufacturer: Davis Standard
Roll Diameter (in.): 3.5
Model:
520034
USED: Davis Standard 75mm extruder, 54" Johnson sheet line as follows: (1) Used 75mm Davis Standard extruder, electrically heated, water cooled, 30:1 L/D vented barrel, 17.26:1 gearbox ratio, 100 hp DC motor, skid mounted with controls and SCR controller, 500# per hour, on stand, new 1990. (1) Used 3.5" Beringer hydraulic screen changerwith power pack. details
|
|
|
70503
USED: Panel sheet line consisting of: 1 panel chiller, 34" wide x 64" long; (48) 2" wide x 1/2" thick cored cooling bars, vertically adjustable, 1/4 hp motor; (1) 24" wide x 75" long belt puller, vertically adjustable, 2 hp DC gearmotor; (1) 8" wide x rubber pull rolls, 7" diameter, vertically adjustable, 1-1/2 hp gearmotor, ratio 60:1, has speed controls; details
|
|
|