40939001
Used- UNILOY MODEL 350R3 6-HEAD BLOW MOLDER, NEW 1988. 6 HEADS ARE SET ON 8" CENTERS, HAVE MAACO 8000 PROGRAMMABLE CONTROL, AND INCLUDES 6 TIE BAR PLATEN WITH (2) SECTIONS EACH WITH 28.5" WIDE X 16" TOP TO BOTTOM CLEAR PLATEN. (3) HEADS PER SECTION. EXTRUDER IS 3.5", WITH 100 HP AC MOTOR AND SIEMENS MODEL 6SE7231-2EB20-3AB0-Z ADJUSTABLE FREQUENCY CONTROLLER. details
|
40939003
Used- UNILOY MODEL 350R2 6-HEAD BLOW MOLDER, SERIAL #4665, NEW DECEMBERL 1998. HAS MAACO 8000 PROGRAMMER, PEDESTAL OPERATOR CONTROL AND 3.5" EXTRUDER WITH 125 HP AC MOTOR AND EATON ADJUSTABLE FREQUENCY DRIVE CONTROLLER MODEL AF5000+. 460 VOLT AC INPUT. HAS SIDE SHIFT CAPABILITIES, 6 HEAD DESIGN ON 10.5" CENTERS IN (2) SETS OF (3). CLAMP HAS OVERALL SIZE details
|
40939004
Used- UNILOY MODEL 400R20, SERIAL #4983 RECIPRICATING BLOW MOLDER. NO SIDE SHIFT. HAS 4-HEAD DESIGN ON 14" CENTERS. OVERALL CLAMP IS 21.5" TOP TO BOTTOM X 68" WIDE. 6-TIE BAR CLAMP WITH (2) COMPARTMENTS EACH 28.5" X 21.5" CLEAR PLATEN. INCLUDES 4" EXTRUDER DRIVEN BY 125 HP AC MOTOR WITH SIEMENS MODEL 6SE7231-8EB20-3AB0-Z ADJUSTABLE FREQUENCY CONTROLLER. details
|
|
|
|
|
|
|
|
|
10755005
Used: Sterling dual 50 lb double - double configuration blow molder. Mounted in a single framework with a central microprocessor control system are (2) blow molders, each with the following: 6" 24:1 L/D extruder wtih 300 hp AC motor and inverter controls; 50 lb accumulator head; first in, first out material flow. 180 ton clamp, 60" wide x 84" long clear details
|
|
|
10755003
Used: Sterling model SE630D accumulator head blow molder. Two heads on 42" centers, 30 lb head shot capacity, 84" x 84" clear platen, 72" maximum and 16" minium daylight, 180 ton clamp force, 6" extruder 24:1 L/D, 300 hp, Barber Coleman Maco 6500 100 PT parison programmer. System includes Maguire 3 component blending system, dryer, hopper, hopper and cyclone details
|
523789
USED: Sterling blow molder, 6" diameter, 24:1 L/D, manufactured in2000. Clamp tonnage 100 tons. Extruder drive 400 hp DC. Plasticizingcapacity 1,650 lb/hour. Shot size: single 30 pound (13.1 kg) head.Head configuration: single. Controls: Barber Coleman MACO 6500, 100point parison programmer. 48 inch wide x 56 inch long clear platen,automatic part take details
|
|
|
88938
USED: Bekum model H-121 continuous extrusion blow molding machine. Dual sided. Shuttle clamp assembly with maximum 2 up production of up to a maximum 5 liter (1.3 gallon) bottle. Single head, single parison with air operated knife assembly and blow pins. 75 hp DC motor on 80 mm, 24:1 L/D extruder. Electric heat with Barber Coleman temperature controllers. details
|
522498
USED: Battenfeld-Hartig model BH717 with twin 15 lb head. Usableplaten measures 72" x 60", 300 ton capacity, platen 18" min daylightand 66" max daylight. 4.5", 24:1 L/D extruder with barrier screw,200 hp DC drive, water cooled barrel, water cooled feet throat.Lufkin gearbox rated for 300 hp, 17.419:1 ratio. Accumulator head(2 each), 15 lb shot size, details
|
|
|
521552
USED: Cincinnati model E-50-A accumulator head blow molding machine.Includes ANSI 151B safety upgrade. ARO regulator/filter/oiler, 165 psicapable ARO air valve for blow air, 1 gallon accumulator on programming circuit, machine wired to 460 volts, ball valve on heatexchanger. Clamp max width is 16", max length is 21", depth (bothhalves) is 10", max daylight details
|
|
|
|
|
|
|
80422
Used: Gerosa 3 re-heat & stretch blow molding machine. Capable of running .250 to 1.50 liter containers with through puts up to 3000 bottles/hour, for 2 liter through put up to 2400 bottles/hour, 3 cavity. Controls are SCS-Static Control Systems Mitsubishi frequency control, 400 volt, Class 380 or 460 volt, 50/60 hz. Total hours 5000. With pre-form dumper details
|
80423
USED: Frontier orientation stretch blow molding machine. 4 blowstation machine with 3 conditioning stations (heating). Programmable controls. Machine has very low hours. Estimated production rate is 3600-4000 bottles/hour. The electrics can be set up for 50 or 60 hz main power. Included are preform feeder and conveyorized preformloader. details
|
74069
USED: Hayssen Econoblow blow molding machine, model 75-S-2500.5 lb FIFO accumulator head with programmable controls and MOOG parison programming. Also equipped with a part take away deviceand a bottom blow module. This machine is disassembled for shipping.The prior owner had retrofit and rebuilt this entire machine at many times the asking price. Equivalent details
|
|
|
|
|
518227
USED: Nissei model ASB-650H orientation stretch blow molder. 29 ozinjection, 480V electrics, two step process machine. Does not includecontrol panel. Plasticizing capacity 16.5 oz. Injection pressure16,000 psi. Screw speed 0-240 rpm. Clamp force 25.1 tons up and 26.5tons down. Clamp opening force 12.4 tons up and 7.25 tons down. Clampstroke 340mm up and details
|
|
|
|
|
|
|
|
|