Einschnecken Extruder Kunststoff Extrusionsanlagen

42634008
Used- PTI 10'' Trident Series Single Screw Extruder,  Model 10000. Approximate 10 to 1 L/D ratio. 3 Zone electrically heated, water cooled non-vented barrel. Closed loop system with pump, tank and heat exchanger. Water cooled feed throat with hopper. Approximate 51'' centerline height. Driven by a 250 hp, 500 volt, 1750/1900 rpm DC motor thru a Flender details

41816002
Used-Coatem CE Synchro 60-2 Single Screw Extruder.  1.77" (45 mm) screw diameter, L/D 30, extrusion capacity 132 lbs/h (60 kg/h). Drive capacity 12 hp/9 kW, installed capacity 33.3 hp/25 kW, (9) heating zones with independent temperature control by a Siemens microprocessor drive controlled by a Toshiba converter. Stainless steel feeder for glue, 6" touch details

42555001
Used- Buss Laboratory Ko-Kneader, Model MKS 30-18 /  E 40. 30mm Diameter single screw, 18 to 1 L/D ratio. Clam shell type barrel electrically heated, air cooled. Water cooled feed throat with hopper. Driven by a 5.5 kw (7.5hp), 3/50/380 volt, 1445 rpm motor with reducer. Includes a discharge screw extruder, 40mm, 6 to 1 L/D ratio, driven by a 1.5 kw (2hp), details

42289003
Used-Cincinnati Single Screw Extruder, type Alpha 45-25B-18-100/150-1100  with AC motor, frequency controlled, gear drive to screw, air cooled nitrided barrel, 9 temperature control zones - 5 for extruder and adapter, 4 for customer's use on tools - single phase, relay controlled with individual temperature controllers, hopper with stop valve and outlet, melt pressure and details

42188001
Used-Cincinnati Pipe Single Extruder, type Proton 45-25B.  45 mm diameter screw. 25:1 L/D. Motor 45 hp/30 kW, 380-400 volt/50 cycle/3 ph. Working capacity approximately 132-152 lbs/hour (60-70 kg/hour) HDPE. Total power installed 72 kW. Electrically heated, air cooled (4 zones) barrel. Including (1) Cincinnati Pipe head and (5) inserts and calibers for 0.98"-1.97" details

42097001
Used- Davis Standard 2-1/2'' Thermatic Single Screw  Extruder, Model 25IN25. 30 to 1 L/D ratio. Electrically heated, air cooled 6 zone barrel. Water cooled feed throat with hopper. Approximate 42" centerline height. Driven by a 50 hp DC motor thru a gearbox ratio 17.26 to 1. Includes a control panel with temperature controllers and a C clamp. details

10351000
Used-Cincinnati Milacron CMS 120-28 GR Single Screw  Extruder. Screw diameter 4.7" (120 mm), 28 L/D, 661 lbs/hour (300 kg/h) throughput, 347 hp/260 kW motor, 18 regulators, S400 s G Cimi coated screw, with diehead adapter, without hopper. details

41816001
Used-Corima Single Screw Extruder, 2.5" (65 mm) screw  diameter, L/D 30, 73 hp/55 kW motor, (5) heating zones for extruder and (3) for tools, with feeder, renewed electrical cabinet. (1) spare screw. details

41722002
Used-Buss PLK 100 Single Screw Extruder. With 3.9"  (100 mm) screw, 7 L/D ratio, 50-350 screw speed, 125 hp (65 kW) motor. New 1979. details

41705004
Used- Davis Standard / NRM 4-1/2'' Single Screw Extruder,  Model 4.5 PM III. 32 to 1 L/D ratio, electrically heated, water cooled, non-vented with 250 hp DC motor, 17.72:1 gearbox ratio. Includes a control panel with 8 zone Eurotherm digital temperature controllers, 6 zone Eurotherm digital die temperature controllers, Eurotherm digital screen changer and melt details

41592002
Used- Davis Standard 3-1/2'' Single Screw Extruder,  Model 3.5MV-350. 30 to 1 L/D ratio. Electrically heated, air cooled, 5 zone barrel. Water cooled feed throat, no hopper. Driven by a 60 hp, 3/60/460 volt motor thru a gearbox ratio 17.4 to 1. Includes a variable speed inverter, a C clamp, and a control panel with Eurotherm model 2208 digital temperature details

41592004
Used- NRM/Davis Standard 3-1/2'' Single Screw Extruder,  Model Pacemaker III 35PMIV. 24 to 1 L/D ratio. Electrically heated, air cooled, 4 zone barrel. Water cooled feed throat, no hopper. Driven by a 75 hp DC motor thru a gearbox ratio 15.25 to 1. Includes a swing gate and a control panel with Eurotherm model 808 digital temperature controls, and a Reliance details

11453110
Used-Davis Standard Thermatic Extruder, model 25IN25.  2.5" diameter screw, 30:1 L/D, 6 heating zones, 50 hp motor, 17.2:1 gearbox ratio, with hydraulic screen changer. Includes Process Controls Corp 4 compartment blender/feeder model EB476DF004 with controls. details

11453107
Used-1.5" Davis Standard Extruder, model DS-15S. 24:1  L/D, electrically heated, air cooled, jacketed feed with hopper, 15 hp DC motor, 15:1 gearbox ratio, 100 rpm screw, 4 zone, pedestal mounted, new 1985. details

11453105
Used-Davis Standard Thermatic Extruder, model 20IN20.  2" diameter screw, 30:1 L/D, 25 hp motor, 17.56:1 gearbox ratio, with hydraulic screen changer. Includes Process Controls Corp 4 compartment blender/feeder model EB476DF004 with controls. details

11453102
Used-2.5" Davis Standard Extruder. 30:1 L/D, electrically  heated, air cooled, 5 barrel zones, 50 hp DC motor with SCR, control panel, with Una-Dyn hopper dryer/loader system, model 200#. New 1995. details

11453100
Used-2.5" APV Sterling Extruder. 30:1 L/D, electrically  heated, air cooled, 5 barrel zones, 50 hp DC motor with SCR, control panel, with Una-Dyn hopper dryer/loader system, model 200#. details

11453098
Used-Davis Standard Thermatic Extruder, model 25IN25.  2.5" diameter screw, 30:1 L/D, 6 heating zones, 50 hp motor, 17.2:1 gearbox ratio, with hydraulic screen changer. Includes Process Controls Corp 4 compartment blender/feeder model EB476DF004 controls. details

11453096
Used-Davis Standard Thermatic Extruder, model 25IN25.  2.5" diameter screw, 30:1 L/D, 6 heating zones, 50 hp motor, 17.2:1 gearbox ratio, with hydraulic screen changer. Includes Process Controls Corp 4 compartment blender/feeder model EB476DF004 controls. details

41242001
Used-Eurotechno Single Screw Extruder. 125 mm (4.9")  diameter screw, 55 kW (73 hp) motor, capacity on LDPE or HDPE 150 kg/hour (330 pounds/hour). details

40883003
Used- Welex 2 1/2'' Single Screw Extruder, Model 250,  approximately 24 to 1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed throat, with hopper. Approximately 45'' centerline height. Driven by a 40 hp, 500 volt, 1750 rpm DC motor with a gearbox, ratio 9.3 to 1. Includes a control panel with Eurotherm and Watlow temperature details

40927001
Used- Genca Single Screw Extruder, Model EB 100245HF2001WE9179,  1" Screw diameter approximate 28:1 L/D ratio, electrically heated, air cooled, non-vented 3 zone barrel. Water cooled feed with a magnet, no hopper. Approximate 44-1/2" centerline height. Driven by a 5 HP, 3/60/230/460 Volt, 1775 RPM motor, gearbox ratio 10 to 1. Includes a control panel with Eurotherm details

40913002
Used- Welex 2" Single Screw Extruder, Model 20024:1RH.  No screw. Electrically heated, air cooled 3 zone non-vented barrel, missing 2 blowers. Water cooled feed throat, no hopper. Driven by a 20 hp, 500 volt, 1750 rpm DC motor thru a gearbox, ratio 10:1. Approximate 43 1/2" centerline height. Includes an incomplete control panel. Mounted on a common base. details

40913007
Used- Akron 3 1/2" Single Screw Extruder, model PAK350,  approximately 24:1 L/D ratio. Electrically heated, air cooled 5 zone non-vented barrel. Water cooled feed throat, no hopper. Driven by a 75 hp, 300 volt, 1750 rpm DC motor thru a gearbox, ratio 13.95:1. Approximate 42" centerline height. Includes a control panel with Gefran controllers. Mounted on a details

40913009
Used- Welex 2" Single Screw Extruder, model 2.00AC.  Approximate 24:1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed throat with magnet, no hopper. Driven by a 20 hp, 500 volt, 1750 rpm DC motor thru a gearbox, ratio 10:1. Approximate 42" centerline height. Includes a control panel with controllers, (1) missing. details

40913011
Used- Akron 3 1/2" Single Screw Extruder, model PAK350.  Approximate 24:1 L/D ratio. Electrically heated, air cooled 5 zone air non-vented barrel. Water cooled feed throat with magnet, no hopper. Driven by a 75 hp, 300 volt, 1750 rpm DC motor thru a gearbox, ratio 13.95:1. Approximate 40" centerline height. Includes a control panel with Eurotherm controllers, details

40913016
Used- HPM 2" Single Screw Extruder, Model 2.0TMC24.  Approximate 24:1 L/D ratio. Electrically heated, air cooled, 3 zone non-vented barrel. Water cooled feed throat with magnet and hopper. Driven by a 20 hp, 500 volt, 1150 rpm DC motor thru a gearbox, ratio 9.4586:1. Approximate 47 1/2" centerline height. Includes a control panel with Eurotherm controllers details

40913018
Used- Single Screw Extruder, approximate 2'' diameter  screw, approximate 24 to 1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed throat with hopper. Driven by a 20 hp, 500 volt, 2500 rpm DC motor thru a gearbox. Approximate 49" centerline height. Mounted on a common base. No controls. details

40733009
Used- Sterling Extruder Corp 1 1/2'' Single Screw Extruder.  Approximately 24 to 1 L/D ratio. Electrically heated, water cooled 4 zone non-vented barrel, no water system. Water cooled feed throat with hopper. Approximate 47'' centerline height. Driven by a 10 hp, 500 volt, 1750 rpm DC motor thru a gearbox, ratio 26.40 to 1. Includes a control panel with Barber-Coleman details

24384000
Used- Baughan Stroud 1'' Diameter Single Screw Extruder,  Model 3500/CL. Approximately 24:1 L/D ratio. 3 zone non-vented barrel, electrically heated, air cooled. Water cooled feed throat with hopper. Driven by a 4 kw, 320/360 volt, 2000 rpm DC motor with a reducer. details

40570002
Used-PTI 2.5'' Trident Series Single Screw Extruder,  model 2500. Approximate 32 to 1 L/D ratio. 5 zone electrically heated, air cooled, non-vented barrel. Water cooled feed throat, no hopper. Approximate 88'' centerline height. Driven by a 50 hp, 3/60-90/460 volt, 1780/2670 rpm motor thru a gearbox, ratio 17.533 to 1, 75 hp rating, catalog rating 150 details

40350001
Used-NRM 2.5" Single Screw Extruder, model PM IV. 2.5"  screw diameter, 24:1 L/D ratio, electrically heated, air cooled, non-vented barrel. Gearbox ratio 15.23:1, 1750 rpm, 1.25 SF, rated 56 hp. Unit driven by a 50 hp DC motor thru a Reliance DC drive and Fenner digital controller. 460 volt, 94 amp. Reported hours used 13,384. Reported manufactured 1990. details

40158016
Used- Akron 1 3/4'' Single Screw Extruder, model M-PAK175,  approximately 24 to 1 L/D ratio. Electrically heated, air cooled, 3 zone non-vented barrel. Water cooled feed throat with a lump breaker, no hopper. Approximately 42'' centerline height. Driven by a 15 hp, 640 volt, 1750 rpm DC motor with a gearbox, ratio 14 to 1. Includes a free standing control panel details

25717000
Used: 1-1/2" single screw co-extruder, driven by a  10 hp DC gearmotor and a control panel with an Emerson electrostat drive. Reportedly built 1989. details

90321
Used- Wilmington-Sterling 6" Single Screw Extruder,  Model 6-1/2, Approximate 30:1 L/D ratio. Electrically heated, water cooled 10 zone non-vented barrel with closed loop system with pump, tank and heat exchanger. Water cooled feed throat with hopper. Driven by a 300 hp, 500 volt, 1750 rpm DC motor thru a reducer, ratio 20.84:1. details

89322
Used- Becz Machine 1.25" Pedestal Mounted Single Screw  Extruder, Model 252.25. Approximate 12:1 L/D ratio. Electrically heated, air cooled single zone non-vented barrel. Water cooled feed throat with hopper. Driven by a 3 hp, 180 volt, 1750/2050 rpm DC motor thru a reducer, ratio 50:1. Includes a control panel with controllers. Mounted on a common base details

88458
Used- Wayne 1" Single Screw Extruder. Approximately  24:1 L/D ratio. Electrically heated, air cooled, non-vented barrel. Feed throat with hopper. Driven by a 5 hp DC motor. Unit includes a control panel with SCR control. All unitized on a common base. details

87794
Used- Welex 2" Single Screw Extruder, Model 200-24:1.  Approximate 24:1 L/D ratio, electrically heated, air cooled 4 zone barrel. Feed throat with hopper. Extruder driven by a 20 hp DC motor thru a reducer, ratio 10:1. Includes a control panel. details

87249
Used- Plasti Program 1.3" Single Screw Extruder, Model  RS35, Approximately 24:1 L/D Ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed with hopper, approximately 41" centerline height. Driven by a 10 HP, 500 Volt DC motor with gearbox. Control panel with Watlow controllers. details

87251
Used- Plasti Program 1.3" Single Screw Extruder, model  RS35, approximately 24:1 L/D ratio. Electrically heated, air cooled 3 zone non-vented barrel. Water cooled feed with hopper, approximately 41" centerline height. Driven by a 10 hp, 500 volt DC motor with gearbox. Control panel with Watlow controllers and a Baldor DC drive. Built 1988. details

86642
Used- NRM Davis Standard 3-1/2'' Diameter Single Screw  Extruder. 24 to 1 L/D ratio. Electrically heated, water cooled, jacketed barrel section. 24.89:1 gearbox ratio, 100 hp DC motor with SCR, control panel with 4 barrel, 5 die zones with temperature controllers, water circulation system with pump, serial #19364, SO #64696. details

522534
USED: Buss K-Neter, type PLK46 Labor. 1.8" (46mm) diameter  single screw. Screw speed 245 rpm by an 11.25 hp/7.5 kw AC motor. Complete with feeding screw. Overall dimensions: 5'2" long x 3.25" wide x 6'2" high (1600mm x 1000mm x 1900mm high). details

85944
Used- Sterling 3.5" Single Screw Extruder, Approximate  27:1 L/D ratio. Electrically heated, water cooled, 4 zone side vented barrel. Approximate 42" centerline height. Closed loop system with pump, tank and heat exchanger. Water cooled feed throat with hopper. Driven by a 75 HP, 500 Volt DC motor thru a reducer, ratio 13.95:1. Unit includes an 18 hole strand details

85845
Used- Cincinnati Milicron 2.5" Single Screw Extruder,  Model Apex, Approximate 26:1 L/D Ratio. Electrically heated, air cooled 4 zone non-vented barrel. Water cooled feed throat with hopper. Approximate 41-1/2" centerline height. Driven by a 40 HP, 640 Volt DC motor with gearbox, ratio 17.86:1. Includes an air conditioned control panel. details

85172
Used- Egan 6" Single Screw Extruder, Model H6026D.  Approximate 26:1 L/D ratio. Electrically heated, water cooled 8 zone non-vented barrel. Water cooled feed throat, no hopper. Includes a reducer, 710 HP rating at 1150 RPM, ratio 7.054:1. Requires motor and panel. details

84897
Used- Egan 3-1/2" Single Screw Extruder, Model H3518HD.  Approximate 26:1 L/D ratio, electrically heated, water cooled 6 zone non-vented barrel with heat exchanger, pump and tank. Water cooled feed throat, no hopper. Includes a reducer, 381 HP rating at 1750 rpm, ratio 7.67:1. Requires motor and panel. Mounted on a carbon steel base. details

522066
USED: 4.5" Sterling extruder, 40:1 L/D, electrically  heated, water cooled, jacketed feed, vented barrel, 400 hp DC motor with SCR controller, 9.62:1 gearbox ratio, 8 zone control panel, on base with (1) spare feed screw, (1) feed section. details

521797
USED: 1.5" Davis Standard extruder, model DS-15S. 24:1  L/D, electrically heated, air cooled, jacketed feed with hopper, 15 hp DC motor, 15:1 gearbox ratio, 100 rpm screw, 4 zone, pedestal mounted. New 1985. No controls. details

521804
USED: 75 mm Davis Standard extruder, electrically heated,  water cooled, 30:1 L/D, vented barrel, 17.26:1 gearbox ratio, 100 hp DC motor, skid mounted with controls and SCR. New 1990. details

83016
USED: Sterling 8" Single Screw Extruder, approximate  20:1 L/D ratio. Electrically heated, air cooled non-vented barrel, no screw. Water cooled feed throat, no hopper. Requires an approximate 450 hp motor. Includes a Sterling gearbox, no tag.Approximate ratio is 32:1 Approximate 49-1/2" Barrel centerline height. Unitized on a common base. details

83018
USED: 4.5" Single Screw Extruder, approximate 22:1  L/D ratio. Electrically heated, air cooled non-vented barrel. Water cooled feed, no hopper. Requires an approximate 150 hp motor. Includes a reducer, no ratio. Approximate 48" centerline height. Unitized on a common base. details

82778
USED: Union Carbide single screw extruder system consisting  of (1) Union Carbide approximate 3" extruder, 304 stainless steel; 16:1 L/D ratio, 3" top feed, 3" end bottom outlet, driven by a 1/2 hp 90 volt DC gearmotor, 56:1 ratio. (1) Accurate single screw dry material feeder driven by a 1/4 hp DC motor with hopper. (1) Bush and Wilton stainless steel rotary details

81842
USED: Prodex Torquemaster 6" single screw extruder,  model TKM60D340-24. 24:1 L/D ratio, electrically heated, water cooled, side vented (locted 91" from feed openeing). 8" x 9-1/2" feed opening. Driven by a 300 hp DC motor, 1750 rpm. 550 volt thru a Lufkin reducer, 14.58:1 ratio. Includes temperature control panel having Barber Coleman digital controls. details

81419
USED: Sterling 4-1/2" single screw extruder, 30:1 L/D  ratio. Electrically heated, water cooled (no system). 5 zone vented barrel (plugged). Water cooled feed throat with hopper, gearbox ratio 13.9:1. Die clamp, approximate 42" centerline height. Unit requires an approximate 200 hp DC motor and control panel. details

79900
USED: Davis Standard Thermatic III, Model 360H II.  3.5" screw diameter, 34:1 L/D ratio, electrically heated, water cooled. 100 hp DC drive thru gearbox, ratio 17.36, rated 161 hp, 1.5 S.F. Unit includes control panel having Barber Coleman controllers. details

520298
USED: NRM Pacemaker III 4.5" lowboy extruder. Machine  has a 24:1 L/Dratio and electrically heated, water cooled (closed loop) barrel atapproximately 24" centerline height. Gearbox is direct driven by a200 hp DC motor with SCR controller. Integral temperature controllerwith rebuilt screw. Mfg 1975. details

79374
USED: HPM 3.5" single screw extruder. 3.5" diameter  x 138" long cored screw, 40:1 L/D ratio, approximate 42" centerline height. 6 zone side vented barrel, 4-1/4" diameter vent, 92" from feed, electrically heated, closed loop water cooled with tank, pump and heat exchanger. 5-1/2" x 4-1/2" water cooled feed (no hopper). Driven by a 100 hp, 1780 rpm, 500 details

76099
USED: Egan 3-1/2" single screw extruder, 36:1 L/D ratio,  vented barrel. Electrically heated, air cooled, 7 zone. Water cooled feed throat, no hopper. Driven by an approximate 150 hp DC motor thru an Egan helical gear reducer, ratio 16.94:1. Approximate 42-1/2" centerline height. Includes control panel with controllers and strand die with clamp. details

72990
USED- Instamelt Rotary Extruder System, Consists Of:  (1) model TL-72 rotary extruder, approximate 14" diameter rotor, electrically heated, water cooled. 3 1/2" x 2 1/2" feed throat with a Plasticolor 3000 proportioning unit. Driven by an approximate 60 HP DC motor thru a Falk reducer, ratio 9.179:1. Discharges into a model 79 gear pump, driven details

70816
Used- Black Clawson 3-1/2" Single Screw Extruder, Model  435. Approximately 30:1 L/D ratio. 6 Zone non-vented barrel, electrically heated, water cooled. Driven by a 150 hp DC motor thru a quick change gearbox. Low/high speed ratios 7.24/1.08:1. Includes Quantum digital temperature control panels, Harland Simon drive. details

70386
USED- Brabender Instrumentss Single Screw Extruder,  3/4", Type 16-02-000. 16:1 L/D ratio, electrically heated, air cooled, 1/60/230 Volt, 15 Amp. Includes Dynisco controls. Requires screw. details

69172
USED: Black Clawson 4 1/2" extruder, 24/1 L/D. Electrically  heated barrel. Gearbox is a Philadelphia change gear type which is direct driven by a 150 hp DC motor. Approximate 24" centerline height. Unit has a rebuilt screw. details

65434
USED: Berstorff Roller Feed Extruder. Approximate 180mm  screw diameter (7.5"). Approximate 5:1 L/D ratio. Cored screw. 8" x 10" feed opening. Jacketed barrel. Two speed gearbox having a 28:1 and 44:1 ratio. 40" centerline height. Includes hinged rotating breaker plate assembly and adapter. No motor or controls. details